Make a bow with your hands from a PVC pipe. How to make a compound bow from PVC pipe yourself. Review of the design of a homemade PVC bow

Hello everyone, I am glad to welcome you to this site. Today I’ll tell you how to make a bow from PVC pipe with your own hands. Of course, the idea on the Internet is not new, but I simply wouldn’t forgive myself if I didn’t make such a bow with my own hands.

For the manufacture of homemade bow from PVC pipes we will need:
- PVC pipe marked SCH 40;
- Construction hair dryer;
- Roll of cardboard;
- Several carpentry clamps;
- Two equal planks (with which we will compress the heated pipe)

Dimensions of a homemade bow made from PVC pipe

Making a bow from PVC pipe with your own hands

The bow is a noble weapon. Since ancient times it has been used to hunt wild animals. Over the millennia, this type of weapon has been improved and improved.

Its modern versions are made from new materials and technologies; they are distinguished from previous products by their range of shots and accuracy of hits.

Many people think that a homemade product will be rough and far from ideal. But by following the advice and carefully watching the video, you can learn how to make a bow from a PVC pipe yourself.

Advantages of PVC products

This device is easy to transport. AND big sizes They don’t interfere at all, because it has a prefabricated device and is very easy to disassemble.

Together with arrows, it easily fits into a quiver. The weight of such a bow is light, but the accuracy is high. A good homemade tool is in no way inferior to its factory-made counterparts in terms of combat capabilities.

This ancient weapons, made with your own hands from PVC pipes, differs from the factory version in less weight. And it differs from its wooden counterpart in higher strength.

A video will help you make a bow from a PVC pipe, where the production is presented in great detail.

The low cost of synthetic materials makes it possible to produce this device at a cost that will be an order of magnitude less than purchasing a finished product.

PVC pipe is considered the simplest and most affordable material option. You can use leftovers after repairs, or buy a small size of the workpiece (3 meters).

IMPORTANT! An additional advantage of PVC bows is their long service life. After all, such a product is not subject to rotting, unlike wood.

What parts does an onion consist of?

The arrowhead can be made from a piece of flattened electrode. After shaping, the tip is inserted into the shaft and lightly sharpened.

Now you know how to do compound bow. Just don’t forget that this is a hunting weapon and a piece of entertainment that can cause great harm owner if used without precautions.

Wounds caused by these weapons can be very serious. And do not forget that its use for hunting purposes is punishable by law.

Before you make a bow with PVC pipes and arrows, think about the fact that these items must be used with extreme caution. Only in this case will you be able to enjoy using this weapon and at the same time not be punished by law.

Why do you need a homemade bow from a pipe? The question is, of course, interesting. IN modern world such a tool is more of a “sports” fun than a real necessity. After all, there is a hunter in every man, so this lesson, although it has turned into a hobby, it has not lost its relevance. Bow hunting is unlikely to be effective, but as entertainment in a safe area, the tool is quite suitable.

In addition, you can make a bow from PVC pipes with your own hands for a child. boy adolescence will definitely appreciate this device. But here it is important to remember safety, especially when making arrows.

As it turns out, you can make a wonderful, functional bow from PVC pipe. To do this, it is enough to consider visual examples, select the correct pipe diameter and related materials. And making a bow from PVC pipe itself is a fairly simple task that only requires attention. In order to better describe how to make a bow from a pipe, we will break the whole complex of actions into several steps.

Material selection

One PVC pipe will be used for all components of the structure. Its diameter is no more than 5-10 mm. It will be divided into several pieces. The pipe walls will have an optimal thickness of 2 mm. Moreover, after assembly the bow will be very light.

The design will consist of 3 parts and 5 pieces of pipe. The classic bow consists of:

• handles;
• bowstrings;
• shoulder

Do-it-yourself bow from a pipe in the video will allow you to visually get an idea of ​​each step of the work. It is better to start manufacturing each element separately. By the way, for convenience you can also use homemade drawing, but if you don’t have drawing skills, you can get by with simpler work. Although it wouldn’t hurt to watch the video or photo material.

Making a shoulder

To make the shoulder stronger, it is advisable to use a PVC cable with a channel 66 cm long. Using special gloves, you need to heat the pipe well using an industrial hair dryer. If this is not the case, it is advisable to find an alternative heating device, but without open fire, so as not to damage the pipe. It is necessary to use gloves or oven mitts, since the pipes heat up quite strongly and quickly when heated.

As soon as the pipes have become plastic, a cable is inserted into them and then the product is heated again. A piece of board, laminate, or wooden beam is suitable for crimping. It is important to press both arms of the bow well.

The excess parts are cut off with a grinder, after which the resulting burrs are trimmed with a file.

The layers on the toes of the shoulders are glued and joined. A hole is drilled in the sock. This is necessary to insert and crimp the metal grommet. They are made from copper or brass tube. First, the rings are inserted into the hole, then flared around the edges. For the convenience of the roller, it is better to use self-tapping screws. Both arms of the future bow are subjected to this procedure.

Handle

She is one of the important elements. The better it is, the more convenient it will be to use the bow. So, the handle must have sufficient rigidity. First, we make one part - the mold. It is turned from wood, after which a molten piece of pipe is driven into it and molded according to the required parameters.

If suddenly the tube has cooled down and the handle is not yet ready, you need to heat it up again. Afterwards, the two parts, the shoulder and the handle, are heated together and inserted into each other.

Boom shelf

To do this you will need toothbrushes (3 pcs.) and a piece of PVC pipe. To do this, the pipe part is molded in the shape of the letter G or T. The upper zone of the part is made under heat in the shape of a half ring. The lower part is attached to the handle cavity with simple fasteners.

To make a slot for arrows, the product is put on a tube with a large diameter, and the second part is connected to the handle and smoothed to its shape. In this case, one hand holds the semi-ring from opening and moving, and the other presses the handle against it.

The head of the toothbrush is wrapped in several layers of tape. This is necessary to prevent damage due to heat. After this, where the brush head passes to the stem, bend it. All parts are connected with small screws.

Bowstring

First, a bow-sized reel is made, after which the fishing line is wound. The two ends of the product are tied together to form a single closed ring, after which the entire string is wound together with the loops.

Decor

After the onion is ready, it can be decorated. For example, paint it in a protective color or in one tone. Thanks to the whiteness of the PVC pipe, the color will be rich and beautiful. It is better to use acrylic paints. Also, for better operation, the bow body can be treated with polymer impregnation.

As for arrows, they can be made of either aluminum or wood. Their shape and degree of sharpness should be chosen based on future use. If the bow is planned for a child, it is better to take safe suction cups.

The result is a beautiful, functional product that will delight “hunters” of any age.

Question: “How to make a bow from PVC pipe with your own hands?” Many people ask. It is not at all difficult to make beautiful homemade weapons from this building material. The material below contains detailed information on how to quickly make an excellent bow and arrow, and also describes the advantages of such a homemade design.

The bow is a weapon. Since ancient times it has been used for hunting wild animals. More than one year, and more than one millennium, have passed since the invention of this device. During this time, the bow mechanism was improved and improved.

A modern bow, if we compare it with its ancient “relative,” is distinguished by the presence of new materials, accuracy and range of shots.

This is confirmed by a bow made from PVC pipes from folk craftsman Maxim Egorov. A lawyer from St. Petersburg became a record holder for viewing his video on YouTube, where he talks about how to make chairs from rope and plastic bottles, how to make a bow from PVC pipe, how to make a phone case from a water gutter. In just a few months, this folk artist has become a real YouTube star.

What are the advantages of such a homemade design:

• Despite its large size, bows made from PVC pipe blanks are very easy to transport. This is possible thanks to the prefabricated structure. After disassembly, such a device along with arrows can be placed in a quiver.
• The low weight of the device makes it superior to factory analogues for hunting.
• High strength. This bow turns out to be much stronger than a homemade device made of wood.
• If a silencer is installed on the string of such a device, then the shots fired by such a bow will be silent.
• If such a device is equipped with a shako, then the combat performance of the bow will increase. It increases the rate of fire and reduces the time to prepare for shooting.

Manufacturing process

Previously, a certain type of wood was used for such a device. Nowadays this issue can be solved much easier. All you need is two pieces of PVC pipe (approximately 1.5 meters each).

The width of such a pipe may vary. The dimensions of the pipe blank affect the power of the structure.

Tools required for work:

• screwdriver;
• self-tapping screws;
• jigsaw;
• drill.

The bow itself consists of three parts. In the center of the mechanism there is a handle, on the sides there are shoulders and a bowstring. All this is enhanced by the internal insert.

Sequence of work:

• The pipes are cut so that their length is the same.
• A handle for the bow is cut out of wood; two prepared blanks will be attached to it.
• Having prepared the handle, there is no need to rush to attach the workpieces. They need to be prepared first. For this purpose, grooves are cut in the end part of the pipes; blocks will be located in them, which are needed for high-quality tension of the bowstring.
• Shoulder attachment. The two prepared pipes will be the arms of the bow. They are not difficult to attach. This can be easily done with a few screws. All fastenings must be made securely.
• The ends of the shoulders are slightly warmed up and bent outward.
• Small notches are made at the ends of the shoulders. They will serve as a place to attach the bowstring.
• The string needs to be pulled very tight. It is recommended to use a strong rope that is resistant to stretching and deformation as a bowstring.

Appearance design

Not everyone makes a big deal of it these days, but in ancient times, every hunter who owned a bow decorated it in different ways. A special meaning was invested in such decoration. Even the smallest detail of the decoration was endowed with great meaning.

A homemade device will become especially individual if you design it to your liking. Bows are decorated in the following ways:

• Painting with special paint for plastic.
• Covered with fabrics and impregnated with polymer. An amateur hunter will be distinguished by a bow covered with camouflage fabric. This design not only decorates the product, but also increases its power. Plastic after this coating easily withstands low temperatures, does not break or crack.

You can use anything you like for decoration, but we must not forget that the structure cannot be overloaded.

Arrows

To check the operation of the device you will need arrows. You can purchase them, or you can make them yourself, which will once again highlight the individuality of your bow.

• Everyone determines the length of the arrow for themselves. It is best to use glazing beads for the boom. You just need to choose them without knots. Their side should be 1 cm.
• From the glazing bead you need to make a round shaft, which is brought to an ideal state first with coarse-grained sandpaper, and then with fine-grained sandpaper.
• Then the tip is made. It is best to make the tip from thin steel and place it in the prepared socket with glue.
• After this, a cut is made for the bowstring. Its depth is approximately 6 mm.
• Arrow fletching. It can be made from paper, plastic, tape and even bird feathers. The most good option feathers for arrows are considered to be turkey feathers.
• At the end the plumage can be painted. Here everything will depend on personal priorities.

Block mechanism

Now it’s clear how to make a bow from PVC pipes and arrows. As you can see from the description, there is nothing complicated about this. And now it’s time to look at how a compound bow is made from PVC pipes.

To work you will need:

• PVC blanks;
• rollers (2 pcs.);
• wooden board;
• jigsaw;
• bowstring;
• toothbrush.

Stages of work:

• First, bow arms are made from PVC pipes. For them, two blanks of 45 cm are prepared.
• Next, the edges of the workpieces are sawed and two rollers are inserted there.
• On the other side, a through hole for bolts is made on each workpiece.
• Handle. The desired design is cut out on a wooden board using a jigsaw. The blanks are secured on both sides of the handle with self-tapping screws.
• Bowstring. One end of it is attached to the extreme part of the shoulder, threaded through both rollers, and then the other end of the bowstring is fixed on the second shoulder.
• Arrow stand. A through hole is made in the handle and inserted into it top part dental mesh. This completes the work.

Checking the bow in action

Now that the manufacturing is complete, it’s time to check the device. To do this, it is recommended to use a sandbag.

First, the bag is placed at a distance of 10 meters. Then this segment is gradually increased. In this way, the maximum range of the device can be determined.

Now, anyone who wants to spend their leisure time in nature in a more interesting way can make their own bow. After carefully reading the above information, the problem: “How to make a bow from PVC pipe with your own hands” will not be so big.” And if you add a little patience and your own imagination to this, you can build a very beautiful and strong bow For sports recreation, which will become an integral part of leisure for a long time. And the huge advantage of such a device is that it contains a piece of the master’s soul.

There are many ways to make a bow from PVC pipe. There are sophisticated ones that require a lot of time and effort. There are simple, convenient ones that allow you to make crafts quickly and get a high-quality product.

For example, to make a non-separable bow structure, you need a PVC pipe approximately one and a half meters long and 25 mm in diameter. Other materials you will need are a wooden board, paint, tape, and aluminum foil. Tools used in the work: hair dryer (well technical); measuring tape; drill; felt-tip pen; hand saw.

Start by marking the pipe. Mark with a felt-tip pen from both ends 30, 60 cm long, as well as the center (middle). In addition, 8 cm segments are measured from the center in both directions.

One of the edges of the 60 cm long pipe begins to be heated with a hairdryer. This is done evenly along the length, constantly rotating the pipe around its axis. After the material has become pliable, the pipe is laid on a flat board, the unheated end is raised by a quarter of the diameter, placing a lining under it. Place a board on top of the heated end, press it down - you can stand with your feet. As a result, a workpiece is obtained in which the pipe remains round in the middle part and has a narrow elliptical cross-section at the end.

Then everything described is done with the other end of the pipe. At the same time, it is fixed so that flattening occurs in the same plane as the first section. In addition, before deformation begins, the opposite end (which is already flattened) is raised by half the diameter of the pipe. Afterwards, a workpiece is obtained in which the middle part (approximately 25...30 cm) remains round in cross-section, and from it to the edges the cross-section changes smoothly from round to elliptical, the latter occurring symmetrically in both sections).

When heating a PVC pipe, do not allow it to heat quickly and unevenly. If this is allowed, the material will lose its elasticity and the craft will not be of high quality.

Afterwards, a section 15 cm long and 15 cm from the end of the pipe is heated with a hairdryer until it becomes round again. It is then positioned so that the previously flattened sections of the pipe are perpendicular to the support. Apply a 15 cm long board to the heated area and flatten it. The same is done with a 15-centimeter section on the other side of the tubular workpiece.

At the final 15-centimeter sections of the pipe, slots are made with outside Luke. Their distance from the ends is 3 cm. The places of the slots are heated, rounded, and loaded through wooden blocks. You can make them round with sandpaper.

Again, sections of the pipe near the 30-centimeter marks are heated - their total length is approximately 8 cm. When heated, they will expand, and the transition section will become smooth. As a result, a smooth tubular blank is obtained, the ends of which are bent in one direction.